Snaplock Machines

Button Punch Snap Lock

Specially designed for commercial and industrial ductwork, these Button Punch Snap Lock machines will turn out perfectly formed locks. They will produce both a female button lock (inboard rolls) and a button-punched right-angle flange (outboard rolls). Two models are available in both a 20 gauges (9-station) and lighter material, and lighter material.

Machine Dimensions

1600mm x 800mm x 120mm High, 350kgs.

Electrics

3hp, 415v 50hz speed approx. 14m per minute.

Button Punch Snap Lock Flanger

Roll single-direction curves down to a minimum radius of 3-1/2″ inside or a 5″ outside radius, almost automatically. These punched right-angle flange curves fit perfectly in the female button lock formed on the Lockformer® 20 gauge Button Punch Snap Lock.

Machine Dimensions

1800mm x 800mm x 1200mm High, 140kgs.

Electrics

1hp, 415v 50hz, speed 6m per minute.

Collar Makers

Collar Maker

Specifications

 

  • Notch, bead, crimp and roll complete round starting collars.
  • 75mm to 400mm in diameter out of 24 to 30 gauge galvanized in one pass.
  • Electrical 1hp, 240v, 50hz.
  • Speed 7 metres per minute.
  • Dimensions – 800mm x 800mm x 1000m – 175kgs.

Spin Collar Maker

Specifications

  • Make your own spin collars in minutes. Cut galvanised stock to width and length, set the diameter and push the blank against the automatic stop.
  • A synchronised die notches the lead edge for easy spin-installation on the job site.
  • The notched piece is then pushed past the stop, feeding the part into the rollformer and finally into the automatic crimping and curling operations.
  • Electrical 1hp, 240v, 50hz.
  • Speed 9 metres per minute
  • Dimensions 1250mm x 800mm x 1000mm – 220kgs.

Round/Oval Pipe Machine

Specifications

  • Available in either 7 or 9 station (for pre-curl) machines.
  • Fabricates both male and female forms for reeves-type snaplock.
  • Each lock is formed on flat sheets with no restrictions on the diameter of the finished pipe.

Cleat Bender

30 inch Manual Cleat bender

Standard: Heavy Cast Iron and Fabricated Steel Construction

Manually Operated, forms uniform drive cleat edge on rectangular ductwork.

Specification Chart

Max. Cap.
Mild Steel
Max. Bending Depth of
Drive Cleat
Dimensions Weight
20g/1.0mm 457mm 12.7mm 65cm x 32cm x 32cm 29kgs
20g/1.0mm 610mm 12.7mm 82cm x 26cm x 28cm 43kgs
20g/1.0mm 762mm 12.7mm 82cm x 26cm x 29cm 68kgs

Snaplock Machines

Button Punch Snap Lock

Specially designed for commercial and industrial ductwork, these Button Punch Snap Lock machines will turn out perfectly formed locks. They will produce both a female button lock (inboard rolls) and a button-punched right-angle flange (outboard rolls). Two models are available in both a 20 gauges.(9-station) and lighter material, and lighter material.

Machine Dimensions

1600mm x 800mm x 120mm High, 350kgs.

Electrics

3hp, 415v 50hz speed approx. 14m per minute.

Button Punch Snap Lock Flanger

Roll single-direction curves down to a minimum radius of 3-1/2″ inside or a 5″ outside radius, almost automatically. These punched right-angle flange curves fit perfectly in the female button lock formed on the Lockformer® 20 gauge Button Punch Snap Lock.

Machine Dimensions

1800mm x 800mm x 1200mm High, 140kgs.

Electrics

1hp, 415v 50hz, speed 6m per minute.

Pittsburgh Model 16 Gauge

These powerful performers offer the HVAC industry day-in/day-out service. The 16 gauge Pittsburgh Lock machines have 7 forming stations with 2 forming positions. One position forms the Pittsburgh lock, while an auxiliary or outboard position has the ability of forming 1 of 8 profiles depending on the contractor’s needs.

Optional Profiles

 

Image ROLLS CAPACITY APPROX.
MATERIAL
USED
Size
Pittsburgh Lock rolls, 5/16″ Pocket 22 to 28 gauge 25mm 5/16″ Pocket
Double seam Rolls (type S)
Double seam Rolls (type L)
22 to 28 gauge
16 to 22 gauge
28mm
33mm
3/8″ Seam
1/16″ Seam
Drive Cleat Rolls 20 to 26 gauge 53mm 1 1/8″ Width
Standing Seam Rolls 16 to 20 gauge 53mm 51 1/8″ Width
Right Angles Flange Rolls 16 to 24 gauge up to 8mm up to 7/16″ High
Combination
3 in 1 Rolls
with
Special
guide
Right Angle Flange 16 to 24 gauge 13mm 1/2″ Height
20g/1.0mm Standing Seam 16 to 24 gauge 28mm 5/8″ Seam
20g/1.0mm Standing Seam 22 to 26 gauge 45mm 5/8″ Seam

16g Auto Guide Flanger

This power flanger has the “auto-guide” feature, which automatically controls the forming of a right-angle flange. It will contour and follow any edge, straight or curved. Using the convenient table slot, the operator merely turns up a starting edge, starts the material through the rolls and lets go. A calibrated dial sets the auto-guide for work with radii as small as 3-1/4″. Flange height available of 3/8″.

Machine Dimensions

800mm x 800mm x 1200mm, Weight 140kgs.

Electrical

1hp, 415v 50hz, Speed: approx 6m per minute.

Pittsburgh Model 20 Gauge

This 5 station rollformer is ideal for air conditioning Duct manufacturers, plumbers and rainwater goods manufacturers. This machine processes 1 mm into what is called the small Pittsburgh female pocket of 5/16″ (8mm) on the inboard station. On the top of the machine the Auto guide power flanger is mounted for the automatic feeding of straights or radius metal to turn up the 6mm male Pittsburgh.

On the auxilliary station you can fit double seam rolls for joining flat sheet (used in tank bottoms, etc.) or drive cleat rolls for forming the female drive cleat for air conditioning duct work.

Electrics are 3 phase 1hp 415v 50hz, gearbox chain and sprocket drive, dimensions: 1100mm x 600mm x 1200mm, weight 160kg.

Optional Profiles

Image ROLLS CAPACITY APPROX.
MATERIAL
USED
Size
Pittsburgh Lock rolls, 5/16″ Pocket 22 to 28 gauge 1″ 5/16″ Pocket
Double seam Rolls 20 to 26 gauge 1″ 3/8″ Seam
Drive Cleat Rolls 20 to 26 gauge 2 1/8″ 1 1/8″ Width
Right Angle Flange Rolls 20 to 26 gauge up to 3/8″ up to 3/8″ High

Cornermatic Plus

The Cornermatic + Plus automatically inserts and crimps
TDC/TDF corners in seconds.

In can inset Eight (8) corners in approixmately 20 seconds
in any gauge.

Features

  • Push the ductwork or fitting into the flange guides and the machine automatically does the rest.
  • Corners are inserted square and fully crimped
  • Note necessary to change the crimping adjustment using different gauges.
  • Quick loading box holds 80 cornser.
  • Corners are shipped pre-sorted in a cardboard sleeve for direct loading to the magazine.
  • Will handle any fitting built to SMACNA standards.
  • Will handle difficult inside angles and tight square throats as well as off size fittings.
  • 415v, 3 phase, 10amp power, air at 80psi.

Cornermatic II Whisperloc Combo

The CORNERMATIC II® ~ WHISPER-LOC® COMBO is a unique, innovative machine that not only inserts and crimps corners into both ends of ductwork but closes longitudinal Pittsburgh seams on the same ductwork when required. This design allows the operator to accomplish both corner insertion and seam closing on one machine without having to handle the ductwork between processes.

The corner insertion is a pneumatically operated process that rapidly and automatically inserts and crimps corners into both ends of ductwork that uses the TDC® or TDF® method of joining. This unit automatically places a corner piece into a corner on each end of the duct and crimps them securely and permanently into place.

The seam closing is powered by an electric motor and gearbox using a Variable Frequency Drive. It will accommodate duct with various end joining methods. It will close the Pittsburgh seam as well as insert corners on any ductwork that uses the duct flanges conforming to T25-a or T25-b under the Duct Construction Standards. It will also close the Pittsburgh seam only on ductwork that uses the raw edge or slip and drive method.

Corners for this automation are quickly loaded into the magazines from the shipping cartons. The corners come oriented and stacked in the carton for quick and easy loading. The CORNERMATIC II® ~ WHISPER-LOC® COMBO is capable of utilizing either standard boxed corners or pre-packaged disposable cardboard sleeves with a simple quick magazine changeover. The standard boxed corner magazines hold 90 corners and the “new cardboard sleeved corners” come loaded with 80 corners per sleeve. The process is virtually noiseless.

Power

415 Volt, 3 phase, 10amp, power, air at 80psi.

Size

30-1/2″ x 34″ x 96 1/8″ (775 x 850 x 2442 mm)

Weight

1800 lbs. (818 kg)

Single Head Corner Caddy

This machine is for the insertion automatically of TDC and TDF Corners. The machine is lightweight and portable for easy transfer to various workstations in your factory. It eliminates your workers bending and hammering corners in, thus greatly reducing the noise. The corners are loaded in the raked back magazine which carries 175 corners which automatically feed one after another. For these machines to work effectively you should buy patented Cornermatic TDC and TDF corners.

For 18 – 26 gauge material, single phase 240v, 90psi air required

Machine sizes

1000mm x 1000mm x 1100mm high, 130kgs.

Dual Head Cornermatic

Automated Ductwork Corner Insertion and Fastening System

This versatile machine features dual heads for corner insertion. The bottom station is fixed and the top station is power adjusted to suit variable duct lengths. This machine is specifically designed to install patented TDC/TDF cornermatic corners. The machine allows you to insert 8 corners in approximately 15-20 seconds with no need for end to end duct, simply rotate corner to corner as the machine inserts corners to both ends simultaneously.

The machine has a magazine top and bottom which holds 170 corners each. The insertion of corners using the dual head Cornermatic saves approximately 3-6 minutes compared to the old hand insertion per duct length. To operate you simply push the duct at floor level into the cornermatic guides and the machine automatically inserts and crimps the corners at both ends.

For fittings the top station can be isolated and only the bottom station utilized.

Ideally the machine should be mounted in a pit approximately 600mm sqaure and 500mm deep to ensure the bottom corner station is level with the floor.

Machine sizes

616mm x 616mm x 2946mm, Weight 450kgs.

Electrical

Single phase 240v 50hz, air 80-100psi.

Cornermatic Corners
TDC/TDF

  • Adaptability – Handy for every job. Cornermatic’s new rigid corners can be easily installed by machine or by hand.
  • Easy Loading – Cornermatic corners are stacked and packed ready for easy loading into cornermatic machine.
  • Quality Workmanship – Corner facilitate jam-free installations into ducting sections.
  • Durability – Added strength and rigidity to duct sections. Maintains quality from packing to installation.
  • Cost Effective – Quantity discounts apply.

Vertical Power Seam Closers

Cornermatic II Whisperloc Combo

The CORNERMATIC II® ~ WHISPER-LOC® COMBO is a unique, innovative machine that not only inserts and crimps corners into both ends of ductwork but closes longitudinal Pittsburgh seams on the same ductwork when required. This design allows the operator to accomplish both corner insertion and seam closing on one machine without having to handle the ductwork between processes.

The corner insertion is a pneumatically operated process that rapidly and automatically inserts and crimps corners into both ends of ductwork that uses the TDC® or TDF® method of joining. This unit automatically places a corner piece into a corner on each end of the duct and crimps them securely and permanently into place.

The seam closing is powered by an electric motor and gearbox using a Variable Frequency Drive. It will accommodate duct with various end joining methods. It will close the Pittsburgh seam as well as insert corners on any ductwork that uses the duct flanges conforming to T25-a or T25-b under the Duct Construction Standards. It will also close the Pittsburgh seam only on ductwork that uses the raw edge or slip and drive method.

Corners for this automation are quickly loaded into the magazines from the shipping cartons. The corners come oriented and stacked in the carton for quick and easy loading. The CORNERMATIC II® ~ WHISPER-LOC® COMBO is capable of utilizing either standard boxed corners or pre-packaged disposable cardboard sleeves with a simple quick magazine changeover. The standard boxed corner magazines hold 90 corners and the “new cardboard sleeved corners” come loaded with 80 corners per sleeve. The process is virtually noiseless.

Power

415 Volt, 3 phase, 10amp, power, air at 80psi.

Size

30-1/2″ x 34″ x 96 1/8″ (775 x 850 x 2442 mm).

Weight

1800 lbs. (818 kg)

Cornermatic II Whisperloc Combo

The quiet, automated way to close Pittsburgh seams in less than six seconds!

Eliminate hammering to close ductwork, large and small Pittsburgh seams, greatly reduce noise levels and speed up duct seam closing in your shop or at the job site. Whisper-Loc will also close both insulated and reinforced ductwork.

The IPI Whisper-Loc features a micro processor with push button controls to allow the top closing station powered head to be moved quickly to facilitate changing duct lengths. The machine features adjustable material clamps and side block adjustment.

The machine operates with any cross section joint, ie. TDC/F, Slip and Drive, Raw Edge, or Slip on Flange.

Electrical

240v single phase, 50hz.

Size

876mm x 876mm x 2413mm, Weight: 700kgs

Rib Rolling/Beading Machines

Q: Why should I buy this Machine? A: If you don’t have a beader, you are probably cross braking, a labour intensive way of strengthening duct work and unless you are extremely careful, the finished product can be out of square and look ordinary. With the beader below, the ribs are all uniform and the duct perfect every time. The beaders are cost efficient and relatively inexpensive to purchase. Once you have one you will wonder what you did before.

With this 6016 Beader, only one operator is needed to produce SMACNA-approved beads 4-5 times faster than cross braking. It forms five beads, on 12″ centers, adjustable to 3mm depth. Maximum capacity is 16 gauge materials and one operator can easily handle sheets up to 60″ wide.

Machine Dimensions

1800mm x 1250mm x 1200mm Weight: 850kgs

Electrical

2hp, 415v 50hz, Speed approx 16m per minute.

PowerPinner™ 7200

Heavy Duty, Portable Hand Welder

The Model 7200 hand welder is a solid state resistance welder designed for use with 16 gauge sheet metal and PowerPoint Resistance Weld Pins.

• Fast weld cycle
• Stronger & more consistent welds
• Less pins on the floor
• Portable wheels/hand truck
• Capable of welding 1/2″ to 2″ pins to 16 gauges metal

The compact size and hand truck feature allows for easy portability around the shop. A light weight pistol grip trigger, ergonomic handle and easy to read controls further simplify operation. The rugged construction and powerful transformer stand up to the demands of constant, heavy use.

This machine is single phase 30 amp Power Pinner suitable for all Gripnail Pins up to and including 50mm in length in all gauges for fastening insulation/ductliner to metal.

Its lightweight and extra-long gun lead makes it perfect for shop or field use. The complete system includes the power pack with adjustable timer, lightweight gun with heavy duty weld/control leads, and a heavy-duty ground lead with spring loaded copper alloy clamp.

• Lightweight welder with powerful transformer
• Welds 12 pins per minute

Specifications

Input Voltage 240 AC 50Hz, 1 Phase
Input Current 30 Amp
Single Phase 50 Cycle
KVA Rating 5.3 KVA
Duty Cycle 50%
Fusing 50 Amp
Open Circuit
Secondary Volts
5.82 VAC
Short Circuit
Secondary Volts
2480 AMPS
Dimensions 400mm L x 200mm W x 200mm H
Cables Gun: 3 metres
Ground: 900mm
Weight (crated) 60kgs

PowerPinner™ 7005 RF

One Step Welding Speeds Production

The new Power Pinner RF has a special program that allows the operator to continuously fasten weld pins while depressing the foot pedal. The RF will keep welding pins until the operator removes his foot from the pedal. This maximizes speed for the fastest possible pinning operation. Flip a switch and the machine returns to a manual mode for larger pieces of duct work.

The PowerPinner –RF features simple, reliable electronic controls and a high output transformer that will fasten 1/2″ to 2″ pins to 16-26 gauge sheet metals. Other features include:

• Dependable Electronic Controls – A programmable logic control unit replaces all timers, relays, reed switches and circuit boards.

• Single Weld Control – Just set the machine for the gauge you want, and everything else is automatic.

• Quick Change Welding Tips – Upper and lower tips can be changed in
seconds; lower tip is reversible for twice the life.

• Automatic Pin Feed – One feeder bowl for all pin sizes.

Specifications

Input Voltage 240 AC 50Hz, 1 Phase, 30 Amp
Air Requirement 2-3 CFM, 80 PSI
Working Depth 1625mm
Anvil Height 915mm
Total Depth 1728mm
Total Width 813mm
Weight 365kgs.

PowerPinner™ Glider 7105 RF

Convenience of a moveable weld head combined
with new step welding speeds production!

The new PowerPinner Glider 7105 Rapid Fire has a special program that allows the operator to continuously fasten weld pins while depressing the foot pedal. This option works when the arm is locked in the vertical posistion and the machine is foot pedal activated. The RF will keep welding pins until the operator removes his foot from the pedal. This maximizes speed for the fastest possible pinning operation. Flip a switch and the machine returns to a manual mode for larger pieces of duct work.

The PowerPinner Glider 7105 Rapid Fire features simple, reliable electronic controls and a high output transformer that will fasten 1/2″ to 2″ pins to 16-26 gauge sheet metals.

Other features include

  • Moving HeadSpeeds production.
  • Flange Cutouts – Permit continuous lining of flat or L section flanged duct.
  • New Improved ReliabilityS – The Power Pinner Glider 7105 Moving Head Welder uses a PLC (Programmable Logic Control) and non-contact
    proximity sensors in place of pneumatic valves and mechanical actuators.
  • Easy To Operate – Simple logical controls reduce operation training.
  • Standard 5 Foot Throat – Fastens large duct sections, reducing material handling.
  • Front Mounted Component Cabinet– Affords easy access for service needs.
  • Visual Load Cycle – Quickly confirms electronic functions.
  • NEMA 12-Rated Electrical Cabinet – Protects electrical component to minimize machine down-time
  • Lightweight Foot Pedal – Allows easy movement by operator; cord protector prevents damage.
  • Compact – Place between work tables for efficient work flow.

Specifications

Input Voltage 240 AC 50Hz, 1 Phase, 30 Amp
Air Requirement 2-3 CFM, 80 PSI
Working Depth 1525mm
Anvil Height 915mm
Total Depth 1805mm
Total Width 815mm
Weight 365kgs.

PowerPinner™ Weld Pins

Power point weld pins save time and money because they perform consistently. Each point is precisely formed to provide optimum electrical resistance and each cap and shank assembly is securely swaged so that pins will feed without jamming, even in older welders. In addition, PowerPoints are shipped in plastic buckets to eliminate shipping damage. The result is continuous production without the expense of having to clear track jams or refasten where pins did not hold.

Features

  • Faster Welds – forged diamond point design creates more electrical resistance for faster welds.
  • Super Sharp Point – 22 degree point is the sharpest in the industry and cleanly pierces the toughest duct liner.
  • Beveled Edge Cap – Prevents tearing of duct liner

Pin sizes available:

12mm, 25mm, 38mm, 50mm.

  • Better Plating – Zinc and chromate plating exceeds SMACNA standards and gives a more professional appearance.
  • More Consistent Feeding – Precise assembly of shands and caps along with a smoother plating reduces feeding problems in tracks of automatic equipment.
  • Applied with Standard Equipment – Easily applied with most standard hand held or hopper fed resistance welders.

Accessory Machines & Tools Cheek Bender

A two-way trunnion keeps the bending bar in position
at the starting point to assure perfect bends throughout the entire
length. Mounting bolts are included. 20 gauge maximum.

Hand Cleat Bender

A rugged tool designed to easily manage the laborious task of
forming the drive cleat hem. Choice of lengths: 450mm,
600mm or 900mm.

Easy Edger

Turn perfect flanges on elbows or other curved fitting as fast
as you can notch them. No gauge to set. Hand clamps to any
bench. 20 gauge maximum.

Blanking Lines

Introducing a Low Cost Hi-tech Coil Line to produce notched, beaded and cut to length blanks for HVAC Duct Manufacturers. This line is the first in a series of Formtek Coil Lines available to the HVAC industry. This Line is specifically aimed at the smaller fabricators on tight budgets, but can produce 5 tonne of blanks in approximately 3 hours.

This machine allows the smaller fabricator to take advantage of better pricing for 5 tonne coils of metal, thus reducing space taken up by steel racks and allows you to make duct in 1400mm increments and minimises losses through excess scrap.

Power Requirements

25amp, 3 phase, 415 volts.

Also check out the

Pro-Ductmatic and Pro-Fabriduct lines for the larger fully automated HVAC Workshops.

Machine Specification

  • Coil Gauge 16 gauge to 1.5 – 0.4mm, Optional – 1.89mm.
  • Coil Width 1550mm max, 152mm min – Optional – 1854mm coil width.
  • Part Length 3048mm max.
  • Part Length Tolerances +/- 0.5mm
  • Processing Speed Up to 22.5m/min
  • Straightener Section Removes Coil Set.
  • PC based Controls preset and monitor machine functions.
  • Compressed Air None required.
  • Beading Section standard pattern 305mm centres.
  • Notching and Hole Punching V and corner notch combination dies for slip & drive, TDC, TDF, Snaplock and Pittsburgh

Options

  • Centre and end hole punching for 8mm and 11mm dia. cross-tie installations.
  • Cleat Roller, Roll Forms 180 degree hems for drive cleats and Snaplock Button Punch.
  • Tie Rod Hole Punching, Male Button Lock and slitting.
  • Pro-Ductomatic comes in two standard models known as short frame or long frame. Frame type is determined by options the customer chooses.

Also available:
Formtek Mansaver for Overhead Cranes for Jibbed Forklifts

1500 x 5 tonne decoiler loading and unloading for Coil Lines fully certified

Insulated Duct End
Cap Rollformer

Specifications

 

  • Four station rollformer for making duct end caps.
  • Dual sided machine.
  • One side fixed tooling for 50mm tall caps.
  • Other side adjustable for 25 OR 38mm tall caps.
  • 25mm leg lengths.
  • Takes precut strips.
  • 15m per minute through put speed.
  • Handles 0.6 TO 0.9mm thick material.
  • 3Kw, 415V, 3Ph,50Hz MOTOR.
  • Approx. size 625mm Wide x 1500mm Lg. x 1100mm High.
  • Approx. weight 550Kg.

Just feed in precut strips and finished caps come out the other end. No wasted scrap metal, simply cut your scrap to the right width to manufacture either 25, 38, or 50mm end caps for insulated duct.

Swager/Crimper/Bead Rollers

This bead roller unit is designed to roll numerous bend profiles in sheetmetal. This machine is capable of running up to 12 gauge steel, depending on the profile. It requires one airline connection and 240v. There are simple selector knobs and switches to control the speed, direction, starting, and stopping of the unit. The unit is also equipped with a regulated foot switch which will produce higher rolling pressure as it si further depressed.

The machine is driven with a 230V AC variable frequency3 phase 1/2hp motor couple to a 24:1 inline gearbox and features 250mm throat gap.

Edgenotcher

Spiral Pipe/Duct Manufacturing

D-Max 1.2 E

The D-Max 1.2E is a revolutionary automatic Spiral Tubeformer. The versatile D-Max 1.2E Tubeformer can produce spiral pipe up to 18 gauge (1.25mm) thickness and has a maximum strip speed of 71m a minute.

D-Max 1.25 & 2.0

D-Max series Spiral Tubeformers are hydraulically powered resulting in a superior combination of speed, strength and reliability. The D-Max series tubeformers also use a flying slitting device. This device allows for a quiet, gasless and clean cut of the spiral pipe.

Gore-Max 1.25

SM Gore-Max 1.25 is your quality, efficient and cost effection solution to the productions of elbows, reducers, end caps and offsets. ISM’s easy-to-operate Gore-Max 1.25 provides you the power to fabricate quality standing seam fittings in-house.

Max-Stitch 1.0 – Stitchwelder

The STITCH MAX 1.0 maximizes your production output and quality! A controlled and consistent longitudinal weld from end to end ensures a remarkable weld every time. The STICH MAX 1.0 utilizes a copper wire as a conductant so the rollers won’t burn the galvanization off the surface like ordinary seam welders.

For more information on this manufacturer, please visit the website: www.ismmachinery.com

Pittsburgh Model 16 Gauge

These powerful performers offer the HVAC industry day-in/day-out service. The 16 gauge Pittsburgh Lock machines have 7 forming stations with 2 forming positions. One position forms the Pittsburgh lock, while an auxiliary or outboard position has the ability of forming 1 of 8 profiles depending on the contractor’s needs.

Optional Profiles

Image ROLLS CAPACITY APPROX.
MATERIAL
USED
Size
Pittsburgh Lock rolls, 5/16″ Pocket 22 to 28 gauge 25mm 5/16″ Pocket
Double seam Rolls (type S)
Double seam Rolls (type L)
22 to 28 gauge
16 to 22 gauge
28mm
33mm
3/8″ Seam
1/16″ Seam
Drive Cleat Rolls 20 to 26 gauge 53mm 1 1/8″ Width
Standing Seam Rolls 16 to 20 gauge 53mm 51 1/8″ Width
Right Angles Flange Rolls 16 to 24 gauge up to 8mm up to 7/16″ High
Combination
3 in 1 Rolls
with
Special
guide
Right Angle Flange 16 to 24 gauge 13mm 1/2″ Height
20g/1.0mm Standing Seam 16 to 24 gauge 28mm 5/8″ Seam
20g/1.0mm Standing Seam 22 to 26 gauge 45mm 5/8″ Seam

16g Auto Guide Flanger

This power flanger has the “auto-guide” feature, which automatically controls the forming of a right-angle flange. It will contour and follow any edge, straight or curved. Using the convenient table slot, the operator merely turns up a starting edge, starts the material through the rolls and lets go. A calibrated dial sets the auto-guide for work with radii as small as 3-1/4″. Flange height available of 3/8″.

Machine Dimensions

800mm x 800mm x 1200mm, Weight 140kgs.

Electrical

1hp, 415v 50hz, Speed: approx 6m per minute.

Pittsburgh Model 20 Gauge

This 5 station rollformer is ideal for air conditioning Duct manufacturers, plumbers and rainwater goods manufacturers. This machine processes 1 mm into what is called the small Pittsburgh female pocket of 5/16″ (8mm) on the inboard station. On the top of the machine the Auto guide power flanger is mounted for the automatic feeding of straights or radius metal to turn up the 6mm male Pittsburgh.

On the auxilliary station you can fit double seam rolls for joining flat sheet (used in tank bottoms, etc.) or drive cleat rolls for forming the female drive cleat for air conditioning duct work.

Electrics are 3 phase 1hp 415v 50hz, gearbox chain and sprocket drive, dimensions: 1100mm x 600mm x 1200mm, weight 160kg.

Optional Profiles

Image ROLLS CAPACITY APPROX.
MATERIAL
USED
Size
Pittsburgh Lock rolls, 5/16″ Pocket 22 to 28 gauge 1″ 5/16″ Pocket
Double seam Rolls 20 to 26 gauge 1″ 3/8″ Seam
Drive Cleat Rolls 20 to 26 gauge 2 1/8″ 1 1/8″ Width
Right Angle Flange Rolls 20 to 26 gauge up to 3/8″ up to 3/8″ High

We are located in Salisbury
we’re open 8:30AM to 5:00PM, visit us now!